Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
Each person will have their private thinking in relation to How to Install a Bathtub Yourself.
Mounting a bath tub isn't specifically brain surgery, however it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult project. If the old tub is easily easily accessible, the job can move immediately; if you have to open a wall to eliminate the old tub as well as position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have qualified yourself for the work and also fit trying it. As opposed to employing a professional to take over a halfway-completed task, it is much better to take into consideration employing one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and also don't require to alter the arrangement of your previous water pipelines.
Your tools and also material list must comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 small points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and also the regular outlet for leakages.
Lastly, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been utilized at least when as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Secure the faucet in position with the producer supplied backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous type must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, creating the water to pass through the wall between the bath and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in usage. The sealer can crack fairly early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very focused on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am assuming you appreciated the blog entry. Sharing is good. Helping others is fun. We treasure reading our article about Tools You Need to Install a New Bathtub .
Book Maintenance
Report this page